assembly instructions three drawer three doors buffet christmas tree shops

Loading...

Malibu - 3 Drawer 2 Door Robe

Assembly Instructions - Please keep for future reference		227/8232
		238/3574
		258/2904

237/1287

258/7679

279/1496

262/6217

258/8032

257/2512

279/1960

255/7788

247/7662

266/7355

249/6612

278/5189

278/0830

Dimensions

Width - 74.5cm

Depth - 50cm

Height - 181cm

MADE IN BRITAIN

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 8 - 04/09/14

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 49.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the

use of power

drill/drivers for inserting screws,

as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth	• From time to time check that	• This product should not be
and mild detergent, do no use	there are no loose screws on	discarded with household
bleach or abrasive cleaners.	this unit.	waste. Take to your local
		authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

1

If you have damaged or missing components, call the

Components - Panels Customer Helpline: 08456 400800 quoting the reference numbers below

Please check you have all the panels listed below

3 Top (D2870A)

(716 x 494mm)

4 Base (D2841A)

(716 x 476mm)

1	Left Side (D2871A)		2	Right Side (D2872A)			5	Drawer Front (D2783A)
	(1808 x 496mm)			(1808 x 496mm)				(710 x 156mm) x 3

6	Left Drawer Side (W370-124LH)	7	Right Drawer Side (W370-124RH)			8	Drawer Back (W682-124BCK)
	(370 x 124mm) x 3		(370 x 124mm) x 3				(682 x 124mm) x 3

10

Plinth (D2873A)

12

Back Rail (D2847A)

(716 x 92mm) x 2

(716 x 92mm)

Drawer Base (T693-367)

9

Rail (D2874A)

Hanging Rail (FHR704)

(693 x 367mm) x 3

11

13

(716 x 92mm)

(704mm long)

Back (X1710-740)

15

(1710 x 740mm)

14 Door (D2857A)

(1198 x 353mm) x 2

2

If you have damaged or missing components, call the

Components - Fittings Customer Helpline: 08456 400800 quoting the reference numbers below

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A			B	C
Wooden dowel (F22)		x 14	Metal dowel (F901) x 6	Plastic Nail (F91)	x 5
D			E	F
Nail (F51) x 33			Small locking		Rail holder
			nut (F3) x 6		(F1014) x 2
G			H	I
40mm Screw (F910)		x 14	25mm Screw (F50) x 8		(F631) x 8
J			K	L
13mm Screw (F79)	x 1		13mm Screw (F63) x 10		Bracket (F327) x 1
M			N	O
19mm Connecting bolt			25mm Connecting sleeve		Hinge plate
(F461) x 2			(F432) x 2		(F523) x 4
P				Q
		Drawer runner (F1004) x 6
					4
R			S	T
Knock-in Peg (F171GY) x 12			9mm Screw (F74) x 6	9mm Screw (F73) x 12
U
Wedgefix (F639) 12

Tools required

Rule																													Hammer																																Cross-head screwdriver
Square																													Bradawl																																Eye protection (when
Scissors																													Electric drill																																using a hammer or drill)
Spirit level																													Step ladder
Ruler - Use this ruler to help correctly identify the screws
mm						10									20									30										40															50					60										70										80										90													100								110										120										130										140										150										160										170

3

If you have damaged or missing components, call the

Assembly Instructions Customer Helpline: 08456 400800 quoting the reference numbers below

Step 1

B

Prepare the 3 drawer fronts

Screw 2 metal dowels B	B
into each of the drawer	B
fronts 5 .		x 3
	5
Note: Tighten the metal
dowels up fully against
the panels.

Step 2

Prepare the drawer sides

Insert a small locking nut E into the hole shown on the left drawer side 6 and the right drawer side 7 .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Attach the drawer sides to the drawer fronts

Push the left drawer sides

. 6 and right drawer sides

. 7 onto the back of the drawer fronts 5 .

Turn the small locking nuts E on the left drawer side 6 and right drawer side 7 .

Note: Turn the locking nuts E clockwise to secure panels - more than 1/2 a turn.

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

6

5

B

4

Assembly Instructions

Step 4

Fit the drawer base

Slide the drawer base 9 down the grooves in the drawer sides 6 and 7 and down into the groove in the drawer front 5 .

Step 5

Fit the drawer back

Fit the drawer back 8 between the drawer sides 6 and 7 . Make sure that the drawer base 9 fits into the groove in the drawer back 8 .

Hold the drawer back 8 in position and tap the knock-in pegs R through the holes in the drawer sides 6 and 7 .

Step 6

Attach the handles

Attach a handle I to each of the drawer fronts

. 5 using screw H .

Note: Do not overtighten the screw.

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 4 wedgefixes U into the front and back grooves, as shown, and tighten up the screws.

9	7	x 3
6	5

		R
	8	7 x 3
R	9
R	6

U U U U

U

x 3

5

Assembly Instructions

Step 8

Prepare the left side

a: Place 3 runners P on the left side 1 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw T .

b: Slide the runner P back the other way and fit the 2nd screw T into the corresponding hole in the left side 1 .

c: Fit 2 hinge plates O onto the left side 1 making sure that the slot is facing towards the finished front edge.

Push a rail holder F into the left side 1 . Make sure that it is fitted straight, in line with the panel edges and then secure with screw K

	edgefront	Finished	T
			P

	T	T
a:		1
	T	P
		P
	P

T

O

O

O

1

c:

K

F

6

Assembly Instructions

Step 9

Prepare the right side

a: Place 3 runners P on the right side 2 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw T .

b: Slide the runner P back the other way and fit the 2nd screw T into the corresponding hole in the right side 2 .

c: Fit 2 hinge plates O onto the right side 2 making sure that the slot is facing towards the finished front edge.

Push a rail holder F into the right side 2 . Make

sure that it is fitted straight, in line with the panel edges and then secure with screw K

T

P

a:	P	P	T
			T
	P	T

b: T T

T

c:

Finished front edge

2

Finished front edge

2

Finished front edge

K

F

O

2

O

O

Finished front edge

7

Assembly Instructions

Step 10

Prepare top and base

a: Tap 2 wooden dowels A into the ends of the top 3 .

b: Tap 2 wooden dowels A into the ends of the base 4 .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

A

a:

3

A

A

b:	plain	chipboard
			surface

A

Step 11

Fit the top and base to the right side

Push the top 3 onto the right side 2 and secure with 2 screws G .

Push the base 4 onto the right side 2 and secure with 2 screws G .

G

2

plain	chipboard
		surface
	4
	Finished
	front edge

8

Assemblly Instructiions

Step 12			A	Plain chipboard
				surface
Prepare the 2 plinths,				x 2
rail
the rail and the back
				10
a: Tap 2 wooden			Plain chipboard		A
dowels A into the ends			surface
of the 2 plinths 10 .		A		Finished
b: Tap 4 wooden				front edge
			11
dowels A into the ends
of the rail 11 .
c: Tap 2 wooden	A	Plain chipboard
		surface		A
dowels A into the ends
of the back rail 12 .

12

A

Step 13

Fit the rail

Push the rail 11 onto the right side 2 .

2

11

Finished front edge

9

Assembly Instructions

Step 14

Fit the 2 plinths

2 people are needed here

a: Push the			G
plinth	10	at the

front of the unit onto the right

side 2 and G secure with screw G .

b: Push the plinth 10 at the back of the unit onto the right side 2 and secure with screw G .

Note: Support the plinth at the back of the unit until the left side has been fitted.

2

10

b:

10

This outer face should be the same colour as the main unit panels

Step 15

Fit the back rail
Push the back rail 12		Finished
onto the right side 2		edge
and secure with screw G .	2	12

Note: Support the back rail until the left side has been fitted.

10

Assembly Instructions

Step 16

Fit the left side and the 4 plastic nails

Push the left side 1 onto the unit and secure with 7 screws G .

C

C C

Tap 2 plastic nails C into the bottom edge of each end 1 and 2 and 1 into the plinth 10 as shown.

Step 17

Fit the back

a: Square up the unit by making sure that measurement x to x equals y to y.

b: Place the back 15 onto the unit.

Nail D around the outside edges of the back 15 .

Note: Nails should be spaced about 150mm apart.

Stand the unit up for the next step.

Warning: The robe is heavy. Lift with care.

	2
	G
	G
	G
	1
	G
C	G
10	G

C G

a: The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y

D

y

15

y

x

11

	Assembly Instructions
	Step 18	a:
	Fit the hanging rails
		13
	and drawers
	a: Push the hanging rail	13
	.13 into the rail holders F .
		F
	b: Starting with the
	bottom drawer, slide
	both the runners P
	forward and locate the	b:
	drawer sides 6 and 7
	between them, lining up	S
	the holes in the drawer
	wrap with the 2nd
	'threaded' holes in the	P
	runners P
	Working from the inside	2nd threaded
	of the drawer, insert 2
		hole
	screws S through the
	drawer sides and out into
	the 2nd threaded hole in
	the runner.
	Note: Do not overtighten
	the screws.
	If they catch on the
	runner you may need to
	loosen them slightly.

Step 19	K		x 2
		K
Prepare the 2 doors
Push fit 2 hinges Q into
each door 14 .	Q		K
			K
Secure each hinge with			14
2 screws K .
Note: Before securing			Q
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.

12

Assembly Instructions

Step 20

Drill a handle hole in each door

Important: Please follow these instructions carefully.

Lay the 2 doors 14 down onto a smooth surface.

Check that the hinges and holes are in the same place as the diagrams.

Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.

Using the pilot hole in the rear face of the door, drill through the hole indicated opposite, using a 2.5mm diameter drill.

Turn the door over and open out the 2.5mm hole that you have just drilled by drilling back through it with a 5mm drill.

IMPORTANT Carefully choose which hole you need to drill in each door

ONLY drill this hole in 1 door

x 1

14

This will be the left door

ONLY drill this

hole in 1 door

x 1

of

14

This will be the right door

13

Assembly Instructions

Step 21

Fit doors and handles

Note: The easiest way to attach each door 14 is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge Q onto the front part of the hinge plate O

The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge Q FLAT against the hinge plate O as you slide it across as far as it will go. Tighten screw A.

c: The hinge Q must be flat against the hinge plate O prior to any adjustment.

d: The hinge Q must NOT be AT AN ANGLE to the hinge plate O when assembled.

This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

e: Attach a handle I to each door 14 using screws H .

B Q

c: d:

Q

B

Note: When fitting the doors, make sure
that the handle hole you had to drill is	e:
nearest to the bottom of each door.

I

H

14

Assembly Instructions

Step 22

Adjust the doors if needed

a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown.

Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.

Loosen screws A on hinge plates and move door up or down as required.

Retighten screw A.

c: Forward and Back adjustment .

Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.

d: Sideways adjustment .

To move door 'out' loosen screw C.

To move door 'in' tighten screw C.

15

Assembly Instructions

Step 23

Joining units together

Fittings have been supplied so you are able to join units together.

Make sure that your first unit is level.

Push the other unit up against the first unit and ensure both units are level.

Check that the ends are flush and in line, then clamp them together.

Using a 5mm drill bit, drill through the 2 holes (shown circled) in the side panel into the adjoining side panel of the other unit.

Push the connecting sleeves N into the holes and then screw the connecting bolts M in from the other side.

16

Assembly Instructions

Step 24

Attach bracket to top

To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket L fitted to the top of the unit.

Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.

Fix the bracket L loosely onto the top of the unit using screw J and mark the wall for the wall fixing.

Swivel the bracket L away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.

Swivel the bracket L back and fix the bracket to the wall, then tighten screw J .

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc.

If in doubt, consult an expert.

Assembly is complete

Warning: The unit is heavy. Lift with care.

J

L

L

L

Top of Unit

W

A Back

L

L of

Unit

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800 and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

17

mireleseastche.blogspot.com

Source: https://manualmachine.com/argos/malibu3drawer2doorrobe/5820613-assembly-instructions/

Share this post